|Frequently Asked Questions
During App development we must always operate under the specifications and guidelines provided by Apple and Google, which suggests that, among other things, that apps and app updates for the App Store and Google Play Store must always be developed using the latest iOS and Android versions. This of course also means that new apps are reserved for the current smartphone operating systems and hardware. Because our products are also security related, we advise that you always use the latest smartphone with the most recently updated version of iOS or Android.
You can find the current minimum requirements for the app in the Apple App- or Google PlayStore depending on your operating system.
In general, any electric door opener connected by direct wiring of the live wire to a door intercom can be tampered with. This applies to every door intercom (for physical reasons) and is also almost exclusively how electric door openers are installed worldwide.
For greater security we recommend that you protect the electric door opener with a tamper contact which has a remote safety relay. We do offer our own door controller A1081 as a solution for this topic in our shop.
Alternatively you can also encrypt the door opener signal via IP and send it to the door opener via your home automation system. We offer a comprehensive API for integration into third-party systems: http://www.doorbird.com/api
The D10x/D20x series has a built-in 433 MHz transceiver, which was originally planned to control additional sensors and remote controls (e.g. garage doors). Unfortunately, there was not only too little demand in this regard, but also a lack of third-party providers using corresponding modules. The 433 MHz module therefore remains inactive.
The D21x series features a built-in 125 kHz RFID reader for access control (Active Reader Passive Tag (ARPT) system), as specified in ISO/IEC 18000-2:2009 Part 2 which makes them compatible with other third party key fobs and card entry systems.
A maximum of up to 200 key fobs can be registered.
The D11x series does not have an integrated RFID module.
As soon as a visitor rings the device a message gets send directly to the Apple / Google push server. In general the operating system of the mobile end device (iOS, Android) manages reception and display of a push notification. The DoorBird App functions as every other App and it usually takes 2-3 seconds until the push notification shows up on your mobile device.
The most common examples are (sorted by frequency of occurrence):
A network component within your network goes into sleeping mode and awakes only through activity of your mobile device again. Solution: Update the firmware of the Wi-Fi components (e.g. router or repeater) in your network
We ship all DoorBird IP video door stations with administration access (e.g. abcdef0000) and one pre-configured app user (e.g. abcdef0001) to be able to quickly install the device and test it.
For an easy input of the data, QR codes are available on the document "Digital Passport" that are valid until the user data in the DoorBird App administration was changed.
If the DoorBird IP video door station is "online" according to the online check (https://www.doorbird.com/checkonline), but the DoorBird app displays an error message when adding the app user for the live view, 99% of the time the pre-configured app user (e.g. abcdef0001) has been changed or even removed.
This can be checked in the DoorBird App:
Settings → Administration → Login → Users → Settings
a) If the app user (e.g. abcdef0001) no longer exists, please create a new user, write down the username and password and then add it by entering it manually.
b) If the app user (e.g. abcdef0001) exists, but the password is different from the Digital Passport document, make a note of the new password and then add them by entering it manually.
Hint: You can use the "Share user data" function to generate a new QR code for the user. You can open the mail client to forward the information or directly generate a PDF that can be saved on the smartphone or shared via other apps.
If it is not possible to log in to the administration of the DoorBird App, although the unit is "online", we recommend a reset to factory defaults as mentioned in the following article:
Please make sure that you are using the latest version of Door Bird App. It often happens that requests relate to outdated app versions. Please also make sure to restart your smartphone/tablet as some issues are related to the operating system.
For devices with a built-in motion sensor, you can activate it in the administration of the DoorBird App (DoorBird App → Settings → Administration → Login → Motion Sensor → Settings).
If the motion sensor is enabled, and you would like to receive push notifications for motion events, you need to enable them separately in the mobile device settings (DoorBird App → settings → click on the added user, e.g. abcdef0001 → push notifications → motion).
Cloud Recording for motion events must be enabled separately (DoorBird App → Settings → Administration → Login → Cloud Recording → Motion Sensor → Settings).
The user must have active permission to view motion events (DoorBird App → Settings → Administration → Login → Users → Settings → click on the correct user, e.g. abcdef0001 → permissions → motion).
Push notifications and Cloud Recording both require the same activated schedule (DoorBird App → Settings → Administration → Login → Motion Sensor → Settings → Schedule for actions → Push notification).
In our experience, Devolo/HomePlug/Powerline adaptors are unfortunately unsuitable for for door communication purposes because they do not transfer all the data correctly. We also know of similar experiences with competing products. Unfortunately, we have no influence on this technology.
All DoorBird IP video door stations come with an integrated free image history.
You can find further information about our "Cloud Recording" feature on the following page:
We offer a comprehensive open API for any kind of third-party integration (e.g. NAS, NVR, VMS, Home Automation, Smart Home etc.). You can find further information online: https://www.doorbird.com/api
In addition, we already offer instructions for many interesting integrations on our DoorBird connect pages: https://www.doorbird.com/connect
You can find the dimensions and further information in the provided data sheets below each product in our webshop: https://www.doorbird.com/buy
Do not hesitate to get in touch if you have any questions regarding our products: https://www.doorbird.com/contact
The DoorBird requires High Speed Internet (Landline): DSL, Cable or Fiber, with DHCP. Internet Upload Speed minimum 0,5 mbit/s or faster. The faster the Internet, the better the image and audio quality. Please do not connect the DoorBird to an 3G/4G/LTE router (Stability, Latency, TCP/UDP package loss).
The DoorBird has been conceived for use outdoors in harsh environmental conditions. Therefore it has been certified in accordance with the IP65 outdoor industry standard and has been accredited to meet the requirements of Protection Class A1 for rain and snow (which is ,for example, the standard in Northern Europe, North America and Canada).
A ring signal is a very time-critical signal in practical use. Therefore, it is not possible to define a sequence for smartphones / tablets that is processed one after the other when a visitor rings the doorbell.
All users are notified simultaneously on their smartphone via push notification and can see the visitor live.
If a user would only receive a signal 30-60 seconds later, i.e. if there is no response from a user previously notified, the visit is already long gone.
Our models support the use of a conventional door release button inside the house to open the front door, garage, etc. without a smartphone or tablet. Please make sure that the button isvoltage-free, e.g. https://secure.effeff.de/index.php?key=produktkatalog&ID=100318&c=effeff&treeID=157526&lang=en
Please make sure to follow the instructions and the connection diagram in the manual.
All models of our IP video door station use a hemispherical ultra-wide-angle lens. This means that a low mounting height is sufficient to display a person in front of a device at minimum distance (~ 50 cm / 20 in).
It is not possible to rotate the camera module or mechanically adjust the lens on any model, so horizontal installation of the IP video door station is not possible.
The camera lens should be installed at a height of at least 145 cm / 57 in.
D11 series: Due to its compact design, this series is ideal for locations where other models could not be installed. For this purpose, we offer additional mounting brackets in our web shop to cope with complicated installation conditions.
Please always check the optimum installation height for your location before installation.
Our products are cloud-based solutions (see also NEST, Dropbox, etc.). For reasons of reliability and security no port forwarding is conducted through the internet (using NAT or DynDNS). Our products establish an encrypted VPN tunnel connection to our cloud server (located in a highly secured data centre in Germany).
Our products rely on the same secure communications technology used by financial institutions for online banking (SSL). The remote access via our cloud-server is free of charge.
It is not technically possible to use our products autonomously without internet access or without access to our cloud servers, as otherwise key functionality like, for example, push notifications (special server security certificates required by Apple and Google), remote access, periodic free software updates etc. would not be available.
The entire solution is tested and approved by the responsible state office of Germany for Data Privacy and Data Security.
If you want to work without a cloud server you may use an autarkic IP system from e.g. Siedle or Gira, which of course do not provide the same functionality. As a provider of intelligent and convenient Smart Home solutions we do not offer products without connection to our Cloud-Server. It is not possible to use of third-party Cloud Services e.g. from Google Drive, ownCloud, Dropbox, Microsoft Azure, Amazon S3 (for security reasons!).
Our IP video door stations support the secure and smooth use with popular smartphones and tablets (iOS, Android) or our IP video indoor station A1101.
On other platforms we additionally offer the possibility for modern web browsers to configure the device using the web administration tool as well as watching the live view using the HTML5 widget.
Web administration tool: https://webadmin.doorbird.com
As fixed internal video unit we recommend the use of our compact IP video indoor station A1101 in conjunction with all DoorBird IP video door stations. The IP video indoor station A1101 comes with a 4“ True Color Display Touch Screen with scratch-resistant tempered Gorilla® glass and excellent audio quality.
In addition we do offer the table stand A8003 which is designed for using the IP video indoor station A1101 on tables and sideboards.
You can find both products in our webshop: https://www.doorbird.com/buy
The DoorBird IP video door station allows up to eight mobile devices (iOS, Android) or indoor stations per call button to the access the live view in parallel.
When someone rings the DoorBird, a push notification is sent to all mobile devices that are registered for the call button and have push messages activated for the DoorBird App.
Our DoorBird IP video door stations are protected against theft with special security screws, like any other high-quality door intercom system.
Current there are only two known cases where a DoorBird IP video door station has been was stolen. In case of theft the device can be completely locked.
In case of theft, you can send us of copy of the official police report. We will find a solution for you.
The BirdGuard B101 is an additional camera that can be operated in our DoorBird App.
The integration of third-party cameras is not possible in conjunction with the DoorBird App.
You can easily integrate the BirdGuard B101 as well as our DoorBird IP video door stations into third-party systems.
We offer further information on integrations into third-party systems: http://www.doorbird.com/faq#id-34
There is a special rawlplug to use when mounting components on a thermal protection wall, e.g. this product: http://www.conrad.de/ce/de/product/484198/
Please clarify this with the manufacturer of your insulation to find out exactly which rawlplug is recommended to be used in this instance. You can find the required diameter of the screws listed in the DoorBird mounting guide.
Our IP video doorstations allow for connection options for standardised electric door, gate or garage openers (two wires). It is possible to connect all door openers that can be used in the range up to a maximum of 24 V (AC/DC) and 1 A. More information and a schematic diagram can be found in the manual of the respective model.
The IP video doorstations do not provide a power supply for the opener. A separate power supply must be provided. For a suitable power supply and further information, please contact the manufacturer of your door opener.
We have not built-in a way to manually configure static IP address details into our firmware. If you must set one of our network devices to work with static IP-address details, you should set this comfortably in your DHCP server / router for the certain MAC address of our network device. Configuring static IP-address details into a device without using DHCP leads to well known problems in practice, so this is never recommended in a modern network.
All DoorBird IP video door stations have a built-in SIP module for integration with various SIP phones and Home-Automation systems to meet advanced audio and video communication needs. DoorBird therefore provides the possibility to perform SIP integrations through a SIP interface that can be accessed via the App (DoorBird App -> Settings -> Administration -> Login -> SIP settings). As SIP is not standardized, any integration has to be configured individually. This is only possible with considerable effort and DoorBird does not provide any support on individual SIP integrations. DoorBird undertakes ongoing development efforts to integrate SIP.
All compatible SIP devices and installation manuals can be found here: www.doorbird.com/sip
In some regions mobile phone network operators block the access to certain services or on standard ports (e.g. HTTP , HTTPS ), e.g. by using a passive proxy server or because of erroneous routing (normally a temporary problem). This case is very rare but it cannot be bypassed without knowing how the mobile phone network operator is blocking which data. A simple work-around for checking is the temporary use of a VPN service, e.g. www.vyprvpn.com (free for a short test).
If a connection is possible using a VPN service, get in touch with your mobile network operator and forward this information: https://www.doorbird.com/downloads/misc/ports_en.pdf
For the devices with integrated WLAN module, we have explicitly included the point "WLAN range" in the product design. Our devices therefore deliver significantly better results than many relevant competitor products.
If you have Wi-Fi problems or need further information on how to set it up, you can find help on the following page: https://www.doorbird.com/wifi
Unfortunately and regardless of our assistance, there are always environments in which Wi-Fi does not work to satisfaction. We have no influence on this, as we already use the maximum antenna radiation permitted in the EU, Canada and the USA.
In general for reasons of stability (availability, reliability) and possible delays for push messages we generally recommend connecting the devices via network cable.
This series has no integrated Wi-Fi module and is operated exclusively via network cable.
If only two wires (and no network cable) are available at the installation location, we offer a solution in our shop with the 2-wire Ethernet PoE converter A1071.
You can find more information on this in the following article: http://www.doorbird.com/faq#id-118
The DoorBird app supports up 10 DoorBird Video Door Stations and additional BirdGuard cameras.
You can switch backwards and forwards between the video door stations and additional cameras within the app by tapping using the tip of your finger.
The following models can be reset to factory settings:
No login credentials (Digital Passport) are required for the reset to factory settings, nor does the device have to be previously set up on the mobile device.
Please go to the "Reset to factory settings" in the DoorBird app under settings and follow the step-by-step instructions.
Please note that the device must be online via network cable for this procedure. Also, the mobile device from which you perform the reset must be on the same network as the DoorBird.
At the end of the procedure you will receive a new "Digital Passport" document, which is sent to the owner e-mail address. If no owner has been registered so far, the e-mail address you entered during the reset process will be used.
Please note that you must leave the device untouched for 15 minutes after a successful reset, as the firmware will also be installed on the device again.
The process is also available as video: https://www.youtube.com/watch?v=he90S2Xljds
You can power up our IP video door stations or our add-on products using one of the following options:
For the correct selection of the DIN rail power supply, please check the following article: https://www.doorbird.com/faq#id-203
For warranty reasons, our devices may only be operated with power supply units purchased directly from us, as these are individually tested and specially certified.
The power supply via PoE is excluded as it is standardized worldwide: https://www.doorbird.com/poe
We generally recommend a hard-wired connection between the IP video door station and the Internet router, as this is almost maintenance- and trouble-free compared to a Wi-Fi connection.
The installation can be realized with a network cable (Cat.5 or better) to transport both network data and power (PoE).
If an installation via network cable is not possible and only simple bell wire is available on site, our 2-Wire Ethernet PoE Converter A1071 offers a good solution and can transport both network data and power (PoE) over two simple bell wires for a distance up to 80 meters (3150 in).
Although the 2-Wire Ethernet PoE Converter A1071 is the smallest device in its class, the receiver does not fit into the housing of current models.
Some space can be provided for installation behind the housing, or alternatively a small housing suitable for outdoor use can be mounted for the receiver.
Further information is available in the manual on our support page: https://www.doorbird.com/support
If you install the DoorBird app on an iOS device, a paired Apple Watch will also work. It is possible to receive push messages on the watch or open the door.
Unfortunately audio communication via Apple Watch is technically not possible, as this is restricted by Apple. As soon as Apple offers an interface, we will implement it.
Please keep in mind that push notifications are only displayed on one of the devices after pairing: https://support.apple.com/en-us/HT204791
D10x/D11x/D20x series: For warranty reasons it is not possible to operate the device with third-party call buttons.
D21x series: It is possible to use the D2100E (Engineering Edition for integration purposes) in conjunction with our product MTM14E for using up to 14 third-party call buttons.
Please make sure to check the data sheet of the products in our webshop and the additional instructions for individual panels: http://www.doorbird.com/downloads/constructional_drawings_d2100e.zip
We do not support Android TV because there is still a very low demand and the distribution also is very limited, e.g. LG relies on webOS, Samsung on Tizen.
Our devices receive automatic firmware updates regularly to introduce new features or match with the latest changes introduced with iOS/Android updates.
The roll-out usually happens in update waves, which means that not all devices receive the latest firmware at the same time, and it can take up to a few weeks before all devices are updated.
As soon as we start the roll-out for a new firmware, we inform about the changes here: https://www.doorbird.com/changelog
An update always only affects the product series that are shown under "Products affected".
It is possible to check the firmware version for a device at any time: https://www.doorbird.com/checkonline
If you want to perform an update, you can do this in the administration of the DoorBird App with the "Check for firmware update" function.
Which menu languages does the D21DKH and D21DKV support on the outdoor display (resident directory etc.)?
The menu language of the outdoor display of the IP Video door stations D21DKH and D21DKV can currently be set via the DoorBird App administration area to the following languages :
For all models of the D10x/D20x series the illumination of the push buttons can be configured.
The setting "On" sets a permanent illumination, the setting "Off" deactivates the illumination and the setting "Automatic" sets illumination when darkness is detected.
The option to change this setting is available in the administration of the DoorBird App ("Button LED").
Regardless of the settings, illumination occurs within the first five minutes after a restart.
All models of the D21x series have permanently illuminated buttons.
We do not offer the option to change the behaviour.
The DoorBird IP video door station does notify you about the connection status after start-up. Up to three signal tones and a voice announcement in English are played.
3 signal tones and the announcement "No Network" indicate that there is no connection to the local network (DHCP, wiring etc.).
2 signal tones and the announcement "No Internet" indicate that an IPv4 address was assigned via DHCP and a connection to the local network exists, but that no Internet connection is possible (Internet outage, firewall settings).
1 signal tone and the announcement "Successfully connected to Internet" indicate that the DoorBird IP video door station has connected to the DoorBird cloud.
The volume for these diagnostic sounds can be switched between "Standard" and "Silent" in the administration of the DoorBird app. (DoorBird App -> Settings -> Administration -> Login -> Expert settings -> System diagnostics volume).
The display is optimized for durability and is already configured for maximum brightness.
If you have a wired network connection for a network camera, access control or door intercom (regardless of the manufacturer) in the outdoor area, it may be advisable to additionally secure this connection in case of security concerns.
For this use case, a firewall can be configured separately to secure the connection at the connected LAN port. The essential requirement for our products is that a direct Internet connection to *.doorbird.net on ports 80 and 443 must be possible.
A complete overview of the ports used can be found in the following document: https://www.doorbird.com/downloads/misc/ports_en.pdf
Please note that we cannot provide product advice for routers or firewalls. The standard models available from your Internet service provider do not always offer such configurations. We recommend getting in touch with your local IT and network specialist, who can advise you on products and configure the firewall accordingly.
In many regions of the world, a time change happens twice a year between summer and winter time.
The IP video indoor station A1101 performs it automatically, but it can take up to 24 hours depending on the region.
The D1101V is our latest and smallest model. This IP Video Door Station is WiFi-enabled, has one switching relay and a Full-HD camera with an integrated 1080p Sony image sensor. The D1101V is available in two versions – separately for surface- and flush-mounting. The mounting housing is included in the scope of delivery for purchases in our webshop.
The D2101V is bigger, has two switching relays and an integrated RFID reader for access control. This model is operated exclusively via a network cable. IP Video Door Stations for single-family residences and buildings with up to three units are available in over 50 colors and surfaces. We also have models equipped with more components such as keypad, display, fingerprint or info modules. Flush-mounting or surface-mounting housings must be ordered separately.
The D11x and D10x product lines are compared in the following document: https://www.doorbird.com/downloads/misc/d10x_vs_d11x_en.pdf
If a power supply via DIN rail power supply unit is required, we offer two DIN rail power supplies in our shop in the category "Accessories", suited for different applications.
1) The following article allows the power supply for one device of the D10x/D11x/D20x/D21x/A11x series:
Please refer to the wiring diagrams of the respective model series in the manual.
A separate DIN rail power supply unit must be planned for each device.
2) The following article allows the power supply of up to 40 devices of the A11x series:
Please refer to the connection diagrams and information for planners in the A11x series manual.
It is not possible to operate other models using this DIN rail power supply.
The Doorbird app supports the global "Dark Mode" of mobile devices. It is available since iOS 13 / Android 10 and can be activated in the display settings of the mobile device.
We do not offer a separate setting for the "Dark Mode" in the DoorBird app.
With the latest update to iOS 14 new data privacy settings were introduced.
In order for the DoorBird app to communicate with our devices on the local network, this must be enabled as a permission under iOS.
When the app is installed for the first time, a pop-up will appear: "DoorBird would like to find and connect to devices in your local network."
This setting must be confirmed with "OK": https://www.doorbird.com/downloads/faq/app_local_en.jpg
The option can be changed later:
iOS settings → scroll down → DoorBird → activate the slider for "local network"
General advice on the subject of "push notifications".
If a push notification is not displayed or remains silent when displayed despite deactivated silent mode, register the device again for push messages by tapping on the registered user in the settings of the DoorBird app (e.g. abcdef0001), deactivate the slider for "DoorBell" below push notifications, go back one step and save, then wait 10 seconds, reactivate the slider for "DoorBird" and save again.
With this action, you register your mobile device again with the push services of iOS/Android for the DoorBird app.
iOS - Apple
The display of push notifications under iOS is documented in the following help article at Apple: https://support.apple.com/en-us/HT201925
If you use an Apple Watch, note the following article: https://www.doorbird.com/faq#id-128
Android - all manufacturers
The main reason for delayed or missing push messages on Android is the power settings. The following overview provides information for the latest Android versions. Earlier Android versions can have different names for the settings, please check the manufacturer support pages.
1) Go to "Settings" → "Battery" → Disable "Performance mode", "Power Saving mode", and "Ultra Power Saving mode".
2) Go to "Settings" → "Battery" → "App launch" → Toggle the slider "Manage automatically" for the DoorBird app to "off" → Activate "Auto-launch", "Secondary launch", and "Run in background".
3) Restart the mobile device
1) Go to "Settings" → "Apps" → "Permissions" → "Autostart" → Set the DoorBird app to always start in the background
2) Go to "Settings" → "Battery & Performance" → "Choose apps" → Select the DoorBird App → Choose "No Restrictions"
3) Restart the mobile device
OnePlus / OPPO
1) Go to "Settings" → "Battery" → "Battery optimization" → choose the DoorBird app and select "Do not optimize".
2) Go to "Settings" → "Battery" → "Energy saver" → choose the DoorBird app and turn off "Freeze when in Background" and "Automatically optimize when an anomaly is detected"
3) Go to "Settings" → "Notifications & Status Bar" → "Notification Manager" → select the DoorBird App and turn on "Allow Notifications", "Display on Lockscreen", "Display at the top of the screen", "Notification Sound and Vibration", and "Priority Notification"
4) Go to "System Organization" → "Security" → "Privacy Permissions" → "Startup Manager" → Activate autostart for the DoorBird App.
5) Restart the mobile device
The display of push notifications is documented in the following help article: https://www.samsung.com/us/support/troubleshooting/TSG01001588/
Please note the information regarding push notification problems in the following article:
All IP video door stations (from firmware 000131) support the upload of a custom ringtone, that is played when the call button on the device is pressed:
DoorBird App → Settings → Administration → Login → Button Sound → Custom Sound
If you get an error message when uploading, the selected file is in an audio format that is not supported.
Please convert your audio file to an MP3 file with 44.1 or 48 kHz with a maximum length of 10 seconds.
You can use e.g. the following converter online for this: https://onlineaudioconverter.com/
The integration of Amazon Alexa/Apple HomeKit/Google Home with DoorBird IP video door stations was planned for a long time.
For data privacy reasons, we have stopped working on the integration with Amazon Alexa/Apple HomeKit/Google Home until further notice.
We will regularly check for Amazon Alexa/HomeKit/Google Home in the future whether there are good, secure and, above all, data privacy-compliant options for integrations available with already existing DoorBird Connect partners.
Currently, we cannot make any recommendations, but refer to the large number of existing integrations with other systems on our DoorBird Connect page: https://www.doorbird.com/connect